Samson GRAPHITE M32 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Digitální klavíry Samson GRAPHITE M32. Corel Ventura - E81310EN.CHP Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 12
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
V2001 Valve Series
Globe Valve for Heat Transfer Oil
Type 3531
Mounting and
Operating Instructions
EB 8131/8132 EN
Edition April 2003
Fig. 1
Type 3531 Valve with mounted rod-type yoke (partial view)
Zobrazit stránku 0
1 2 3 4 5 6 ... 11 12

Shrnutí obsahu

Strany 1 - EB 8131/8132 EN

V2001 Valve SeriesGlobe Valve for Heat Transfer OilType 3531Mounting and Operating InstructionsEB 8131/8132 ENEdition April 2003Fig. 1 ⋅Type 3531 Valv

Strany 2

5. Description of nameplateFig. 3 ⋅Nameplate1Valve type2Model number3 Model index 4 Order number or date5K value8 Nominal size9Nominal pressure11 Perm

Strany 3

6. Dimensions in mm7. Customer inquiries Should you have any inquiries, please sub-mit the following details:Type designation and order no. (see name

Strany 4

SAMSON AG ⋅ MESS- UND REGELTECHNIKWeismüllerstraße 3 ⋅ 60314 Frankfurt am Main ⋅ GermanyPhone: +49 69 4009-0 ⋅ Fax: +49 69 4009-1507Internet: http://w

Strany 5

ContentsPage1. Design and principle of operation . . . . . . . . . . . . . . . . . . . . . . 41.2 Technical data . . . . .

Strany 6 - 1.2 Technical data

General safety instructionsGeneral safety instructionsThe control valve must be mounted, started up and serviced by fully trainedand qualified person

Strany 7 - 2.2 Strainer, bypass

1. Design and principle of operationThe Type 3531 Globe Valve is based on themodular design principle and can be com-bined with a pneumatic or electri

Strany 8

Fig. 2 ⋅Sectional drawings8.25.36.16.244.14.24.3X44.24.44.36X561451011121314326.36.45.41.1X5.155.21.236.3216.4159 7 8.1DN 15 to 25DN 32 to 50DN 65/80E

Strany 9

1.2 Technical dataValveDN 15 to 80 ANSI 1/2" to 3"Nominal pressure PN 25 Class 150/300Type of connection Flanges Type B1 acc. to EN 1092-1,

Strany 10 - 5. Description of nameplate

2. InstallationValve and actuator are assembled by themanufacturer.For more details on the actuator used,please refer to the corresponding mountingand

Strany 11 - 50 (1.96)

Note!The tightening torques and special tools re-quired for installing and removing the seatare listed in the table on page 9.Important!Prior to carry

Strany 12

3. Place the gasket (1.2) onto the valvebody. Then insert the complete bonnetinto the valve body.4. Align the flange (5.4) and tighten thenuts (1.1) a

Komentáře k této Příručce

Žádné komentáře