Samson S2000 Provozní pokyny Strana 42
- Strana / 124
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
over piping. An adapter available as an ac
-
cessory is used for this purpose:
Threaded bushing
(M20 x 1.5):
G ¼
¼ NPT
0310-2619
0310-2550
NOTICE
The adapter uses one of the M20 x 1.5 con
-
nections in the housing which means just
one cable gland can be installed.
4.10 Mounting parts and
accessories
Should other valve accessories be used
which vent the actuator (e.g. solenoid valve,
volume booster, quick exhaust valve), this
exhaust air must also be included in the
purging function. The connection over the
adapter at the positioner must be protected
with a check valve (e.g. check valve G ¼,
order no. 8502-0597) mounted in the pip
-
ing. Otherwise the pressure in the positioner
housing would rise above the ambient pres
-
sure and damage the positioner when the
exhausting components respond suddenly.
42 EB 8384-4 EN
Attachment to the control valve – Mounting parts and accessories
Table 1 · Direct attachment to Type 3277-5 Actuator (Fig. 4)
Order no.
Mounting parts
Standard version for actuators 120 cm² or smaller 1400-7452
Version compatible with paint for actuators up to 120 cm² 1402-0940
Accessories for
the
actuator
Switchover plate (old) for Actuator Type 3277-5xxxxxx.00 (old) 1400-6819
Switchover plate new for Actuator Type 3277-5xxxxxx.01 (new)
1)
1400-6822
Connecting plate new for Actuator Type 3277-5xxxxxx.01 (new)
1)
: G
1
8
and
1
8
NPT 1400-6823
Connecting plate old for Actuator Type 3277-5xxxxxx.00 (old): G
1
8
1400-6820
Connecting plate old for Actuator Type 3277-5xxxxxx.00 (old):
1
8
NPT 1400-6821
Accessories for
the
positioner
Connecting plate (6)
G ¼ 1400-7461
¼ NPT 1400-7462
Pressure gauge bracket (7)
G ¼ 1400-7458
¼ NPT 1400-7459
Pressure gauge mounting kit (8) up to max. 6 bar (output/supply)
St. steel/brass 1400-6950
St. steel/St. st. 1400-6951
1)
Only new switchover and connecting plates can be used with new actuators (Index 01).
Old and new plates are not interchangeable.
- Mounting and 1
- Operating Instructions 1
- EB 8384-4 EN (1300-1613) 1
- EB 8384-4 EN 3 3
- EB 8384-4 EN 5 5
- Vent opening 6
- 2 Article code 7
- 3 Design and principle of 8
- 3.1 Additional equipment 9
- 3.2 Communication 10
- 3.2.1 Configuration using 10
- TROVIS-VIEW software 10
- 3.3 Technical data 11
- 12 EB 8384-4 EN 12
- 4 Attachment to the control 14
- 4.1 Direct attachment 16
- 4.1.1 Type 3277-5 Actuator 16
- 4.1.2 Type 3277 Actuator 18
- 4.2 Attachment according to 20
- IEC 60534-6 (NAMUR) 20
- 4.3 Attachment according to 22
- VDI/VDE 3847 22
- Actuator stem 24
- EB 8384-4 EN 25 25
- 4.4 Attachment to Type 3510 28
- Micro-flow Valve 28
- 4.5 Attachment to rotary 30
- 4.5.1 Heavy-duty version 32
- 4.6 Reversing amplifier for 34
- 4.6.1 Reversing amplifier 34
- (1079-1118 or 1079-1119) 34
- From the positioner 35
- Control signals to 35
- 4.7 Attaching an external 36
- 4.7.1 Mounting the position 36
- 1.1, 1.2 14.1 3 14 99.1 38
- 4.7.3 Mounting the position 39
- 2 1 1.1, 1.2 40
- 4.9 Air purging function for 41
- 4.10 Mounting parts and 42
- 44 EB 8384-4 EN 44
- Table 6 · General accessories 45
- 46 EB 8384-4 EN 46
- 5 Connections 47
- 5.1 Pneumatic connections 47
- 5.1.1 Signal pressure gauges 47
- 5.1.2 Supply pressure 47
- 5.2 Electrical connections 48
- EB 8384-4 EN 49 49
- 24 V DC BE1 BE2 50
- EB 8384-4 EN 51 51
- 52 EB 8384-4 EN 52
- Connections 52
- 6 Operator controls and 53
- 7 Start-up – Settings 56
- 7.1 Defining the valve closed 56
- 7.3 Adapting the display 57
- 7.5 Checking the operating 58
- Manual reference variable 59
- EB 8384-4 EN 59 59
- 7.6 Initialization 60
- Default No 65
- Nominal range 65
- (locked with Code 4 = No) 65
- EB 8384-4 EN 65 65
- 7.7 Zero calibration 68
- 7.8 Reset to default values 68
- 7.10 Setting the bus address 69
- 8 Operation 70
- 8.1 Enabling and selecting 70
- 8.2 Operating modes 71
- 8.2.1 Automatic and manual 71
- 8.3 Malfunction/maintenance 73
- Error caused by pin 74
- 9 Adjusting the limit switch 75
- 10 Maintenance 78
- 12 Firmware update (serial 78
- EB 8384-4 EN 79 79
- 14 Code list 80
- Code list 81
- 82 EB 8384-4 EN 82
- 84 EB 8384-4 EN 84
- 86 EB 8384-4 EN 86
- EB 8384-4 EN 87 87
- Initialization errors 88
- 88 EB 8384-4 EN 88
- Operational errors 90
- 90 EB 8384-4 EN 90
- Hardware errors 91
- Error appendix 92
- 92 EB 8384-4 EN 92
- Data errors 93
- 94 EB 8384-4 EN 94
- Diagnosis errors 95
- 15 Dimensions in mm 96
- EB 8384-4 EN 97 97
- Heavy-duty version 98
- Light version 98
- EB 8384-4 EN 100
- 102 EB 8384-4 EN 102
- EB 8384-4 EN 103 103
- 104 EB 8384-4 EN 104
- EB 8384-4 EN 105 105
- 106 EB 8384-4 EN 106
- EB 8384-4 EN 107 107
- 108 EB 8384-4 EN 108
- EB 8384-4 EN 109 109
- 110 EB 8384-4 EN 110
- EB 8384-4 EN 111 111
- 112 EB 8384-4 EN 112
- EB 8384-4 EN 113 113
- 114 EB 8384-4 EN 114
- EB 8384-4 EN 115 115
- EB 8384-4 EN 117 117
- Model 3730-43 118
- or 3730-53 118
- EB 8384-4 EN 119 119
- 122 EB 8384-4 EN 122
- EB 8384-4 EN 123 123
Související produkty a manuály pro Audio zesilovače Samson S2000
Audio zesilovače Samson 1400 Uživatelský manuál
(12 stránky)
(12 stránky)
Audio zesilovače Samson 1200 Specifikace
(60 stránky)
(60 stránky)
Audio zesilovače Samson B Series B900 Manuál
(60 stránky)
(60 stránky)
Audio zesilovače Samson Cque 8 Uživatelský manuál
(24 stránky)
(24 stránky)
Audio zesilovače Samson SCOM Specifikace
(67 stránky)
(67 stránky)
Audio zesilovače Samson S1000 Uživatelský manuál
(5 stránky)
(5 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.153 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce